ECCPP Towing Mirrors fit 02-08 for Dodge for Ram 1500 03-09 for Dodge for Ram 2500 3500 Pickup Truck Power Heated Tow Folding Side View Black Mirror Pair Set Right Passenger and Left Driver Side

Almost Perfect. Almost (Read before you buy).
I recently purchased and installed these mirrors. Following up EECCP contacted me via e-mail to make sure everything was alright with my purchase. I sent them the following e-mail.Good moring EECCP Auto Parts,I have received the mirrors and installed them on my 2006 Dodge RAM 1500 Quad Cab 4×4 pickup. I am fully satisfied with the product. They are solidly built and will support my trailer towing needs perfectly. I would/will give this product a good review. I did have some issues/problems during the install that I’d like to bring up. I was able to deal with them and get the mirrors installed to my satisfaction, but they may be things you’d like a chance to address in future production runs. This information would also be good for new prospective customers to know for when they make the decision to purchase this product. I will detail the issues I dealt with in this message. I have pictures of all the items I’m going to line out, but I’ll save those for the Amazon review. Nothing really bad.1. There was a jagged tab on the passenger side mirror that appeared to be left over from the injection molding process. Initially I thought it might be a tab designed to go into some sort of retention or alignment slot. I took the passenger side mirror off my truck for comparison. There was no associated tab on the original mirror nor was there any slot in the door to receive any such tab. From the shape and location of the tab and close examination of the tab I believe that this is most likely a leftover from the injection molding process. I applied a small amount of pressure to see if it would cleanly break off. No such luck. It was very firm and ridged. Finally I decided to take it off with an angle grinder and cutt-off wheel. This worked perfectly. No damage to the face of the mirror body. This did require close attention and a steady hand, but it did buzz right off.2. The electrical sockets on both mirrors (driver and passenger side) were not snugged down. The screws were sticking out of the mirror backs far enough that they prevented the mirrors from lying flat against the door. After several attempts to get the mirrors to lay flat, I spotted the problem. I was able to snug the screws down to where it appeared they were meant to go. After that, the mirrors could lay flat against the door no problem. Again, this was the case on both the driver’s side and passenger side mirror.3. The forward most stud mounted in these mirrors is too short. I’ve installed the mirrors on my 2006 Dodge RAM Quad Cab 1500 4×4 pickup. I don’t know if other year pickups have a different setup. I don’t think so since I did see this problem mentioned in the product reviews from a few other customers on Amazon. I can’t say this was completely unexpected. All three of the studs mounted in these mirrors are equal length with about a quarter inch of un-threaded stud at the end of each. In the forward most mounting whole, the un-threaded portion is all that makes it through. No way to get the provided nut onto that stud. I was able to easily take the original stud out of the original mirrors, and not so easily take the provided stud out of each of the new mirrors. Not so easily because the base of the studs in the new mirrors is round. The base of the originals is hexagonal making it easy to get a wrench on. The recommendation from some other customers through their Amazon product reviews worked. Not exactly easy, but it did work and I was able to get them out and replace them with the studs off the original mirrors. FYI, the original studs are exactly the same length as the new ones. The difference is that originals are threaded all the way out making it possible to get a nut on them and secure the mirrors.4. The exterior plastic of the mirrors did not completely conform to the truck. On the leading edge or forward most edge there is a detectable gap between the door and the mirror. Also where the molded plastic meets the window rubber. The plastic is squared off and the rubber is more round. The top at least on the driver’s side also appears to be slightly warped outward preventing it from completely laying down. It appear that part of the problem is the mold. Or at least a difference in the mold and my truck. I’m not exactly sure what the other part is. The areas that don’t quite lay down at least appear to be the correct shape. Not sure what could be done there. Maybe a heat gun, but I know I would mess that up. They fit close enough that no one will see it if I don’t point it out. They do look good.As you can see, these problems were minor. They did require a bit of mechanical ability, at least one tool not everyone will have, and some trouble shooting know how. In the end, I think these very minor problems could be solved with one small designed changes (choice of mounting studs), and better quality control (clean up the injection molding residue, and tighten the screws). As I’ve said, they are installed and working perfectly. I’m happy with the product, especially for the price.Thank you for making contact with me, and I hope this input is helpful.

Easy to install they are study and well build

Theses mirrors were a perfect fit from my truck and look great. I recommend jumping online to see how best to take off the door panel to get access to the 3 bolts holding on the mirror. Take the whole door panel off. Had both sides done in about an hour. Old mirrors had the typical dodge over extended mirror issue so they no longer locked in place and these new mirrors were an easy and cost efficient solution.

Good